Tel: +86-769-88996313

E-mail: sf@camda.cc

250 KW Biogas Generator

Ratings *Ratings at 0.8 power factor Performance Data * The above fuel consumption is calculate with the natural gas whose heat value is 35.8MJ/Nm 3 Dimensions and Weights Engine Brand & Model: HGKT19 Engine Data Iginition system and sensor: ◇The generator uses ALTRONIC (ECU) and equipped...

Send Inquiry
Product Details


KDGH300-BG    50HZ1(001).jpg


Ratings

Rated  Power

kVA

375

kW

300

Voltage type

50Hz, 380/220V, 3 phases and 4 wires

*Ratings at 0.8 power factor


Performance Data

Engine Brand & Model

HGKT19

Alternator Brand & Model

LSA47.2VS2/300KW

Control System

Deepsea DSE6120

Standard Noise Level@7m (Soundproof Sets)

75 dBA

Circuit Breaker Type

3 Poles MCCB

Frequency & Phase

50hz 3Phases + 4Wires

Engine Speed (RPM)

1500

Fuel Consumption (Nm3/hr) 100% Load

86.19

* The above fuel consumption is calculate with the natural gas whose heat value is 35.8MJ/Nm3


Dimensions and Weights

Content

Open type

Soundproof Sets

Dimensions: (mm)

L

3500

5600

W

1250

2000

H

2020

2500

Weights (kg)

3380

4985


Engine Brand & Model: HGKT19

Engine Data

No. of Cylinders

6 in-line

Engine power(KW)

341

Cycle

4 Stroke

Cylinder Type

Wet

Bore * Stroke (mm)

159 * 159

Compression Ratio

11.5:1

Induction

Turbocharged & Aftercooled

Displacement (L)

18.9

Cooling Method

Water cooled

Governing Type

Electronic

Starting method

24V DC motor

Coolant capacity, including radiator (L)

115

Lubricant Oil

15W40-CF4 or above grade

Oil pan capacity (L)

87


Iginition system and sensor: 

◇The generator uses ALTRONIC (ECU) and equipped the high voltage circuit to realize the high energy and best ignition of gas generator. The minimal speed of ignition is 100RMP and the maximal speed of ignition is 4000RMP, the ignition angle range from 5 to 35.

◇The core of ECU actually is computer chip, which has tre-buttons signal input ( rotated speed, load and temperature). According to the signal, the computer will act the right judge to do the positive cylinder, right time ignition and speed limited protection. 

◇Check every circuit to see connecting joint whether is liable or damaged, high voltage winding whether damaged or leaking electricity.

◇Check the ignition of spank whether nomal, if not, please change it immediately, check the battery voltage not lower than 25V ( Because voltage too low will affect the normal running), please charge to the battery in time.


Combining adjustment of shaft sensor and trigger vane:

After installation of shaft sensor, it should adjust the location ot trigger vane. The method is to install the Cylinder one on the TDC( end point of compression) location, then justify of trigger vane small chip's back limb front-end to the shaft sensor's geometric center as following. Meanwhile, the depth of trigger vane's inserting sensor is 9.5±0.2mm.


If the gas intake pipe happed back flashing, please check:

Whether ignition signal wire keep in the appointed position;

Whether the inner gear of signal generator loosed;

Whether ignition high voltage winding damage;

Whether earth connecting liable.

Problem Processing Method: Contact the manufacturer.


If the power of generator is insufficient, please check:

Whether the filter of voltage regulator valve clogged;

Whether the air filter clogged;

Whether the exhaust pipe clogged.


Pressed air:

Don't use the pressed air or gas to clean clothes or body. The small drops can also cause serious damage in the situation of high pressure. 


2.jpg


Hot Tags: 250 KW biogas Generator, China, suppliers, manufacturers, factory
Related Products
Inquiry